New Products

Meyer Drive Pro Mounting Carton 18504 Colorado / Canyon (used). This was on the truck for two winters. Brackets bead blasted 95%. Three coats of satin black. Includes new Hardware Kit 08138, install instructions. WE ONLY HAVE ONE OF THESE TO SELL.

Meyer 22154 Touchpad 24" Extension cord. This is just a 24" extension cord to allow the controller to be where you want it in the cab. 6 pin rectangular M/F ends. Made to order here in the shop.

Genuine Meyer Lift Arm 13142 for Home Plow by Meyer. Item #4 on the parts diagram.

Meyer 23061 Marker Turn Signal Harness with Relays. Two examples shown in pictures, you will be getting ONE of them, you can't choose. Original design was taped, current design is braided.

USED Driver's Side Back Door for Meyer Nite Saber II. This is a unicorn, we never sold these before, and only have this one. Meyer does not offer new, and usually when a light is destroyed the cover is shot too. Some scratches, otherwise perfect condition

This is new territory for me. I don't like to sell used parts because of the problems that often come along with it. That said, tested, bead blasted, painted silver, lead repaired as/if needed. May not be cosmetically perfect, but 100% spec.

This is new territory for me. I don't like to sell used parts because of the problems that often come along with it. That said, tested, bead blasted, painted silver, lead repaired as/if needed. May not be cosmetically perfect, but 100% spec.

This is new territory for me. I don't like to sell used part because of the problems that often come along with it. That said, bead blasted, tested, painted silver, lead repaired as needed. Not perfect, but 100% spec.

Exactly what it says. This kit allows you to use Pin Type Couplers on your E-58H unit with either 21856 or 22144 NPT hoses. You do NOT have to use the E-58H style that are prone to failure. This is used when replacing an E-47, E-57, or E-60 with an E-58H.

Long story short, this was a loaner E-58H I kept on hand. The thing is, it NEVER got loaned out, not even once. So time for it to go. Meyer moved on from the E-58H a long time ago. I kept it as a spare for my E-58H new plow customers under warranty.

Nite Saber Light Connector Caps - For Plow Light Harness from light. These were cut off new wiring during installs. We include a zip tie to secure it to the existing wiring harness.

Nite Saber Light Connector Caps - For female Socket on Module C Harness. These were cut off new wiring during installs. We include a zip tie to secure it to the existing wiring harness.

Check Ball Set - Pilot Check Ball, Pump Check Ball, B Check Ball; E-47, 57, 60. Set of the (3) Balls pictured. Other parts depicted for reference only.

Home Plow by Meyer Wireless Control Kit - Hydraulic Auto Angling ONLY! In November 2021 Meyer discontinued the wired 22826 hand held controller and replaced it with this as the only option; to convert your existing wired controll

Genuine Meyer Truck Side Harness 23033 for SOS, original design12 pin connector (later replaced by16 min connector). Truck Side Harness for SOS, original design 12 pin connector (later replaced by16 pin connector). 12 pin connector shown for reference. Co

Genuine Meyer 1.5" PA Ram Retaining Rings 07773 (GUIDE RING 1-1/2 RAM) sold in pairs. Fits ALL Meyer 1.5" Rams. Replaces nylon in current PA Rams. Also called "Split Bearing" or "Split Bushing".

Genuine Meyer (Bucher) Motor E-70, E-72, V-70, V-71 and many Monarch units Meyer Part# 15096. Meyer/Bucher switched to a single lug motor. These are the "good ones". New old stock direct from Meyer. May have stains on them, they are not pristine after...

Meyer Nite Saber II Nite Saber III Low Beam Bulb Retainer Clip made out of Stainless Steel. Open up your light, yours may be about to crumble. Replace your mild spring steel with this STAINLESS one.

Genuine Meyer Hardware Kit 08149 Toyota Tacoma Drive Pro Mounts 18502/18533.

Package deal on all 4 ribs for ST Series plows. Genuine Meyer. Use these to build your own Moldboard, or to repair a Moldboard. Used on ALL ST Series Moldboards.The ST Series has been discontinued over 10 years now, these must go!

Meyer EZ Plus Ford Mounting Carton 17162 Hardware Kit 2 - 08876. This one contains the long handle bolts. View diagram for a complete list of what is included in this kit.

Meyer EZ Plus Ford Mounting Carton 17162 Hardware Kit 1 - 08875. Look at the diagram for a full list of what is included.

Meyer EZ Custom 1983 - 1987 Chevy GMC Strap 10398 (fits LH or RH). We have one pair of them available. Sold each. They are OBSOLETE. NO RETURNS.

Genuine Meyer 19781. We call it a Pin Bar, Meyer calls it a PIN PULL WELDMENT. It is the flat bar with the two pins attached. We include a new spring and cotter pin to make installation easier. We have a limited number of these on hand at this low price!

Trip Bumper Drive Pro Plows (PAIR of 22686). Sold in pairs, only fits Drive Pro Moldboards.