Meyer Couplers and Fittings

We chose to put these videos on a DATA DVD. It MUST be played on a computer. It will not play in a conventional DVD player hooked up to a TV. The reason we chose this route is because at just over 5.5 hours in length, it would require 3 DVDs to fit it al

90° Swivel Fitting 21855C for Meyer E-47 pumps, and Angle Rams on plows equipped with E-47 pumps. One is typically on the pump, and one is on the passenger side angle ram. Photo shows two, price is each! Color may vary, silver or gold.

Hydraulic Coupler Set (Pin Type) 1/4" NPT Female thread. Pricing is for one set, a MALE half, and a FEMALE half. ONE set is pictured. Might be Zinc Chromate (gold) or Zinc plated (silver) we cannot control the color. NOT MADE IN CHINA

Exactly what it says. This kit allows you to use Pin Type Couplers on your E-58H unit with either 21856 or 22144 NPT hoses. You do NOT have to use the E-58H style that are prone to failure. This is used when replacing an E-47, E-57, or E-60 with an E-58H.

Genuine Meyer E-58H Hose 22461 (Hose Ass'y. SAE 1/4 x 38" Long M-6 Faceseal). Standard hose included with E-58H Hydraulic Carton. Sold individually.

Genuine Meyer Adapter 22652 to connect female E-58H Coupler to male standard 1/4" pipe thread hoses used on E-47, E-57, and E-60 units. Sold in PAIRS.

Genuine Meyer Female Coupler half 22443C fits E-58H units and Xpress plow units. This is the one that goes on the end of the hose.

Geniune Meyer Female Coupler Half 22445C. This is the one that screws into the Valve Block on E-58H and Xpress plow units.

Genuine Meyer Male Coupler half 22442 fits E-58H units, and Xpress plow units. This is the Male one that screws into the Valve Block.

Genuine Meyer Male Coupler Half 22444C, goes on the end of the hose. Fits E-58H and Xpress plow units.

Genuine Meyer Xpress Plow Hose 22395 33" long, SAE 1/4" Hose used on E-78 units, and on the E-68 and E-88 Xpress Plow. On the Xpress plow it is the Driver's side Angle Hose, and the Mount Cylinder bottom hose. On the E-78 it is used for BOTH Angle Hoses.

Hose Kit for Meyer E-47 / E-60 with 1/4" NPT threads. This kit will work with any NPT E-47 or E-60 and allow you to replace what you have, or upgrade from the old design that had the 90° Swivel Fittings. See FULL DESC...

Here is a set of dust caps for your couplers on some Meyer E-47's, all E57's and some E-60 pumps. Fit most 1/4" quick couplers. The Couplers pictured ARE NOT INCLUDED and are for display purposes only. Again, THE COUPLERS ARE NOT INCLUDED.

Coupler Kit for Meyer E-58H hydraulic unit. ONLY FITS E-58H Unit.

We put together an Upgrade Kit to allow you to replace the old PA Block on your Meyer E-47 or E-57. The Kit includes a brand new 16016 PA Block, adapters to use included Pin Type Couplers, A Cavity Plug, and Wiring Adapter. You just have to cut off the A

Meyer E-47, E-57 & E-60 Female Valve Block Coupler Set 15822. SAE Thread Female Coupler for Valve Block, and Male NPT Thread Coupler for Hose end. Meyer decided to sell this set and replace M22294 with this part. View all images to see part installed.

Meyer E-57 & E-60 Male Valve Block Coupler Set 15821. Male Coupler for Valve Block, and Female Coupler for Hose end. Meyer decided to sell this set and replace M22293 with this part. View all images to view part installed.

In 2014 Meyer switched from the original steel fill plug on the E-72 and V-70 to a yellow plastic plug that strips before it even gets tight.Here is the steel plug to replace the plastic one, or your lost steel plug. It is important to not over-tighten

Genuine Meyer Coupler fits E-57 units and some E-60 units. It has SAE Male threads and screws into the SAE Elbow on the Valve Block. ****NO LONGER AVAILABLE ** REPLACED BY M15822**** THIS IS NOT FREE.

Meyer Plow Cutting Edge Bolt Kit 08184 (9 Bolts, 9 Lock Nuts) Set of (9) 1/2" x 2" Cutting Edge Bolts, fit Meyer plows and others. Also includes (9) Nylock Nuts. Grade 5, Zinc Plated. Fits ST-78 up to C-8 plows (ALL Meyer plows up to 8.5').. NOT for LP-9,

All you need to replace the hoses on your E-47, or E-60 Meyer Plow Pump. Includes two hoses, two swivel 90° fittings, and two pin type coupler sets. Click on Related for another Hose Kit that eliminates the 90� Swivel Fittings, and has Genuine Meyer Ho

90° Elbow. Referred to as "Short Elbow". Used on E-60 units, and some E-47 unit Valve Blocks. ****Redesigned October 2014***

Tall 90° Elbow used on E-47 and E-60 pumps, and E-60 Angle Rams. E-60 units use one tall, and one short elbow on the Valve Block, and two tall elbows on the angle rams.

Coupler fits E-57 units and some E-60 units. It has SAE Male threads and screws into the side of the Valve Block. ****NO LONGER AVAILABLE**REPLACED BY M15821*****